IEC 4 Way Outlets Power Strip with Circuit Breaker , Rocker Switch Controll PDU Power Distribution Unit
Description
This hard wired type power strip is good for installation in your office, rackmount, workbench, industrial and telecom applications and so on. It is not for normal wall outlets. There is no power cord and plug with this unit. A lighted and covered On/Off switch helps prevent accidental shut-offs, while the circuit breaker guards against dangerous circuit overloads. Its sturdy all-metal extruded aluminum housing stands up to demanding network, laboratory or factory environments.
Features
- 5" to 14” - Durable Aluminium alloy Metal Housing Power Strip
- 4 Black ( white or grey or other) IEC C13 Outlets, Vertical or level Outlet Orientation
- Hardwired without Power Cord for Mounting at Your Desired Location
- One IEC C14 Input on Each Side
- Electrical Ratings: 100-125V 60Hz 15A
- UL C-UL Approved and Listed
- Outlets 0.12" to 8.39" (3mm to 213mm) apart center to center
With IEC C13 Cable Easier put in C14 inlet and quickly Installation - Higher Efficiency
Parameter
| OUTPUT |
| Frequency compatibility |
50/60Hz |
| Output watts |
2400W |
| Output volt amp capacity (amps) |
10A 13A 15A 16A |
| Outlet quantity / type |
4*IEC320 C13 |
| Outlet spacing |
0.12to 8.39" (3 to 213mm) (center to center) |
| INPUT |
| Recommended Electrical Service |
15A 125V/13A 250V/16A 250V/10A 240V |
| Input connection type |
IEC 320 C14 |
| Input plug features |
Black or other |
| Input cord length (ft.) |
5 to 25 |
| Input Housing length (in) |
12-1/4 to 72 |
| Input cord gauge, type |
14AWG/3 SJT |
| Function: |
IEC 320 socket converter |
| Voltage compatibility (VAC) |
125 |
| LAMP ALARMS & SWITCHES |
| Rock Switches with circuit breaker and lamp |
Lighted 2 position switch controls power to all outlets |
| Locking switch cover |
Transparent on/off switch cover prevents accidental turn-off |
| PHYSICAL |
| Unit Dimensions (HWL/mm) |
32*60*L/34*43*L |
| Material of construction |
Aluminum |
| Mounting accessories included |
Includes mounting clips |
| Receptacle Color |
Black or other |
| AC line cord color |
Black or other |
| Overload Protection: |
Yes |
| Form factors supported |
Supports vertical or horizontal mounting in rack enclosures, raceways, laptops cat and a variety of other applications |
| CERTIFICATIONS |
| Power Tap |
IEC |
| Approved by |
CE |
SAFETY WARNING:
Installation work of this unit must be done by a professional, a licensed electrician or an electric engineer.
Never install this unit during a thunder storm.
Switch off the power before you start installation work.
This unit is for indoor use only.
This unit is not intended for use in or around wet or potentially wet areas including, but not limited to, aquariums, saunas, showers and fountains.
Risk of Electric Shock!
INSTALLATION GUIDE:
Before installation, you may need to get a IEC C13 Outlet. Decide your wire gauge, and ask store attendant for assistance what color of connectors you should get) from your local hardware or electric supply or home improvement stores.
Minimum tools required: A fine to medium fine philips screw driver, and a pair of scissors, and a pair of mid size slip joint pliers
1. Turn off electricity in the house
2. Decide where to place this unit
3. Choose the side you want the cord exit to choose IEC C14 Built in power strips
4. Match the color of the wires and secure the wire connection with proper wire connectors built in IEC C13 plug.(different wire gauge use different colored wire connectors)
- Mount the power strip where you want it to be:
A) For power strips with mounting tabs on both ends: screw down the unit on the floor, wall or in your cabinet or on your rack, where you want it to be
B) For power strips without mounting tabs, but to be mounted with clips, place the unit where you want it to be first, make marks where to install the clips, which normally should be placed about min 2”<power strips length away from each end, and then screw the clips down with screws provided. Then, snap the power strip in on the clips
- Push IEC C13 outlet plug into IEC C13 inlet power strips , and push switch to ON. Turn electricity back on, you are ready to go.
Note:
We also accept to custom for our customers.
Product Tags:
|
|
4 Outlets PDU Power Strip and Switch with Overload protecter , Smart Multi Plug Extension Cord Images
|
